Welcome to PCForumz.com!
FAQFAQ      ProfileProfile    Private MessagesPrivate Messages   Log inLog in

AK77 600GN RAID Boot Problem

  
   Hardware Problem Solving Community! (Home) -> AOPEN RSS
Next:  crt w/ fuzzy lines  
Author Message
CrazzyRepairs

External


Since: Oct 26, 2005
Posts: 1



(Msg. 1) Posted: Wed Oct 26, 2005 2:55 pm
Post subject: AK77 600GN RAID Boot Problem
Archived from groups: alt>comp>periphs>mainboard>aopen (more info?)
When my AK77 600GN boots the SATA RAID BIOS appears and the following
appears with it
Scan devices, Please wait...
press <Tab> key into user window!

I have not got any SATA HDDs installed, I have tried everything to get pass
this screen, USB keyboard does nothing, (plan to try PS/2) tried different
IDE HDDs, different cables, CDROMS, RAM, PSU, to solve this but have got
nowhere, in the manual it says u can disable this but u can't! except with a
BIOS update which I can't as I can't load from floppy, CDROM, I have also
tried clearing the CMOS, didn't work. would taking the battery out help?
Anybody got anything else for me to try?

Any replys, thanks

 >> Stay informed about: AK77 600GN RAID Boot Problem 
Back to top
Login to vote
Anssi Saari

External


Since: Jan 04, 2004
Posts: 19



(Msg. 2) Posted: Thu Oct 27, 2005 11:55 am
Post subject: Re: AK77 600GN RAID Boot Problem [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
"CrazzyRepairs" <crazzyrepairs.DeleteThis@ntlworld.com> writes:

> I have not got any SATA HDDs installed, I have tried everything to get pass
> this screen

At least on my MAX version of the board, it goes past that screen
automatically. Even without any drives connected.

> USB keyboard does nothing, (plan to try PS/2)

I think there's a setting in the bios to enable USB keyboard support,
is that on?

 >> Stay informed about: AK77 600GN RAID Boot Problem 
Back to top
Login to vote
Display posts from previous:   
Related Topics:
AK77-600GN Stability problem - The problem is: The board won't run stable if the speed settings are correct. If i set the clock on 100Mzh in stead of 166 (Then the Ahtlon2800 appears to be an Athlon 2100 and RAM runs at 266MHz insteadof 400) it runs OK. Addition of a system fan, chang...

AK77-600GN and GF5700LE 256MB compatibility problem? - Hi, Running XFX GF5700LE AGP8x 256MB at 8x causes: - in DirectX9.0 DXdiag missing DirectDraw B&W rectangles and bouncing block in small window and full screen (only 1st time). - flashing polygons / triangles in 3D games when moving. Installed lat...

AK77-600GN - Just put an AMD Athlon 3200+ (Barton) in my motherboard and I am a little confused over the settings. I have the latest BIOS (R1.08) but the BUS is shown as 200MHz with a ratio of x11. Is this correct? Dave

AK77-8XN Boot up problems - ak77-8xn ATI Radeon 7500 BIOS Rev 1.14 On a cold start the system appears to hang right when the Windows XP Home screen should be displayed. When doing a warm boot the system appears to have no problem and will load windows. Has anybody experienced..

Ak77-8xn "Inaccessible boot device" after flashing - Hello aopen users! I have a Aopen Ak77-8xn board. I used to run bios r1.13 and updated to the recently released r1.15. After rebboting the windows 2000 boot process starts and gives me a "inaccessible boot device" error and refuses to go furt...
   Hardware Problem Solving Community! (Home) -> AOPEN All times are: Pacific Time (US & Canada) (change)
Page 1 of 1

 
 You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



[ Contact us | Terms of Service/Privacy Policy ]