 |
|
|
|
Next: Thunder i7500 NO POST! NO BEEPS!
|
| Author |
Message |
External
Since: Dec 19, 2006
Posts: 3
|
(Msg. 1) Posted: Tue Dec 19, 2006 9:14 am
Post subject: Tyan S2895 / K8WE Power led blinking, no boot
Archived from groups: alt>comp>periphs>mainboard>tyan (more info?)
|
|
|
I have Tyan S2895 / K8WE which has performed quite well. Now, today I
powered my computer off and now when I try to power it on, only power
led starts blinking. No fans rotating, PSU does not seem to start. I
tried to connect pins 15 & 16 on PSU and then PSU fan started to rotate
and it gave power to peripherals. Still, MB won't boot.
Any ideas? |
|
| Back to top |
|
 | |
External
Since: Dec 19, 2006
Posts: 2
|
(Msg. 2) Posted: Tue Dec 19, 2006 8:06 pm
Post subject: Re: Tyan S2895 / K8WE Power led blinking, no boot [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
On 19 Dec 2006 09:14:38 -0800, samppa DeleteThis @w-rock.net wrote:
>I have Tyan S2895 / K8WE which has performed quite well. Now, today I
>powered my computer off and now when I try to power it on, only power
>led starts blinking. No fans rotating, PSU does not seem to start. I
>tried to connect pins 15 & 16 on PSU and then PSU fan started to rotate
>and it gave power to peripherals. Still, MB won't boot.
>
>Any ideas?
Hi ho there samppa,
Have a 2895 for bout a year now and couple o weeks ago a power
on gremlin arrived here also. Not quite the same. Power on button only
works for a very brief moment. the led and fans do try to spin and that
is all. Resetting from the micro switch on the board does the same. The
board will boot if it is un plugged for about 10 - 15 seconds and re
plugged. Board generally will boot after use if done within a few
minutes. Board always will restart if done immediately. Haven't yet
gotten to look for any answers other than the usual few minutes of
googling to the various forums. for the most part i see no fault in
operations when running and hope it keeps that way until i kick out the
home steading gremlin. I notice this board never shuts down the earth
net connectors. Now they do after some time of shutdown fail. Perhaps
its connected. shutdown 20 minutes and dsl modem eth0 stayed lit and
system boots normally. will leave modem on with system off tonight and
see if in the morning the eth0 goes down and system does not boot then.
S2895a2nrf, Antec true power 2 550w atx12v, 2-242's, 2g corsair
cm72sd512rlp, wd1600js-00m, sblive sbo410, samsung ts-h552u,
micro-star gf6600 video card. SuSE 10 amd64smp, KDE Desktop on single
disk with default Riserfs and dsl rarely on connection.
Much nicer than me ole p133 system. tim |
|
| Back to top |
|
| |
External
Since: Dec 19, 2006
Posts: 3
|
(Msg. 3) Posted: Tue Dec 19, 2006 11:46 pm
Post subject: Re: Tyan S2895 / K8WE Power led blinking, no boot [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
no spam please wrote:
> Hi ho there samppa,
> Have a 2895 for bout a year now and couple o weeks ago a power
> on gremlin arrived here also.
I'm sad to hear that you are also suffering from these problems.
Anyway, I have filed an issue to Tyan's support, let's see if I'll hear
something from there. I will also try with a new PSU if I get any life
into that machine.
Best regards,
Samppa >> Stay informed about: Tyan S2895 / K8WE Power led blinking, no boot |
|
| Back to top |
|
| |
External
Since: Dec 19, 2006
Posts: 3
|
(Msg. 4) Posted: Wed Dec 20, 2006 3:51 am
Post subject: Re: Tyan S2895 / K8WE Power led blinking, no boot [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
|
|
| Back to top |
|
| |
External
Since: Dec 19, 2006
Posts: 2
|
(Msg. 5) Posted: Wed Dec 20, 2006 4:38 am
Post subject: Re: Tyan S2895 / K8WE Power led blinking, no boot [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
On 20 Dec 2006 03:51:25 -0800, samppa.TakeThisOut@w-rock.net wrote:
>Now the MB is working again. I replaced the PSU with a new one and
>there are no more boot problems. Old PSU was Fortron FSP460-60PPN and
>new one is "BeQuiet Straight Power Quad Rail 600W" (BQT E5-600W).
>
>Best regards,
>Samppa
Glad yours is working. Will try a ps when i find time. this morning
it was the same. pull the plug for more than 5-10 seconds and box will
boot. tim >> Stay informed about: Tyan S2895 / K8WE Power led blinking, no boot |
|
| Back to top |
|
| |
External
Since: Dec 23, 2006
Posts: 1
|
(Msg. 6) Posted: Sat Dec 23, 2006 10:18 am
Post subject: Re: Tyan S2895 / K8WE Power led blinking, no boot [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
Disconnect everything including the PSU and reconnect, Do clear CMOS
http://www.tyan.com/support/html/clear_CMOS.html
If this fails try removing the battery for a few minutes.
Good Luck
samppa.RemoveThis@w-rock.net wrote:
> I have Tyan S2895 / K8WE which has performed quite well. Now, today I
> powered my computer off and now when I try to power it on, only power
> led starts blinking. No fans rotating, PSU does not seem to start. I
> tried to connect pins 15 & 16 on PSU and then PSU fan started to rotate
> and it gave power to peripherals. Still, MB won't boot.
>
> Any ideas? >> Stay informed about: Tyan S2895 / K8WE Power led blinking, no boot |
|
| Back to top |
|
| |
External
Since: Mar 04, 2007
Posts: 1
|
(Msg. 7) Posted: Sun Mar 04, 2007 10:45 pm
Post subject: Re: Tyan S2895 / K8WE Power led blinking, no boot [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
I had the exact same problem this weekend with the same board.
In my case, the power on switch on the front panel of the case had come
lose. I had to put it back in place and wedge it in with a make shift
shim to get the unit to power on again.
Perhaps this will help.
samppa.TakeThisOut@w-rock.net wrote:
> I have Tyan S2895 / K8WE which has performed quite well. Now, today I
> powered my computer off and now when I try to power it on, only power
> led starts blinking. No fans rotating, PSU does not seem to start. I
> tried to connect pins 15 & 16 on PSU and then PSU fan started to rotate
> and it gave power to peripherals. Still, MB won't boot.
>
> Any ideas?
> >> Stay informed about: Tyan S2895 / K8WE Power led blinking, no boot |
|
| Back to top |
|
| |
| Related Topics: | Intermittant USB on TYAN Thundar K8WE s2895 - I've got one of the above motherboards with the Ultra 320 SCSI controller on board. Quite often (most of the time) it will refuse to power up any USB device no matter if connected to the headers or the rear panel. Other times it will work fine. I've....
Tyan K8WE (S2895) and Cooler Master Hyper 6+ in Lian-Li 2000 - I tried to install a Cooler Master Hyper 6+ on my socket 8 Italy 270 processor on my Tyan K8WE (S2895) motherboard in a Lian-Li case and I did it incorrectly and fried the motherboard. Maximum PC says I can safely use this cooler, but I wanted additiona...
Zalman CNPS 9500 LED, K8WE (S2895) and Factory Tyan/AMD 94.. - I have seen other posts regarding using the Zalman CNPS 9500 LED with Socket 940 motherboards. My question is whether you can use the Zalman heatsink with the factory Tyan/AMD Socket 940 base? I don't want to have to take the motherboard out of the cas...
Tyan S2895 / K8WE BIOS 1.04 "out of space for Option ROMs!" - I have a Tyan Thunder K8WE / S2895 and just upgraded the BIOS to the lastest version 1.04 Now the BIOS hangs up during booting, and it says: "out of space for Option ROMs!" what does this mean? I disabled a couple of on-board devices ...
K8WE S2895...when? - anyone know when this MB is to be in supply? Thanks! ofd |
|
You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
|
|
|
FAQ
Profile
Private Messages
Log in
