 |
|
|
|
Next: USB cards - Opti chip set
|
| Author |
Message |
External
Since: Jul 16, 2003
Posts: 4
|
(Msg. 1) Posted: Thu Jul 17, 2003 1:19 am
Post subject: SD11
Archived from groups: alt>comp>periphs>mainboard>fic (more info?)
|
|
|
Help anyone,
I just put a new SD11 mobo in a Compaq 5900Z, replacing a OE version of the
SD11 that I thought was bad. It would not reboot. (tries to but would seem
to go into sleep mode instead) Anyway, SD11 was cheap on ebay so I got one,
put it in and, viola, it does the same thing! So I cleared the bios setting
with the jumper, rebooted, and it still goes into sleep mode. (I'm not sure
it really is in sleep mode, but the monitor goes into low power, and the
booting process stops. If I clear the bios & hit the switch, it says cmos
setting bad, cmos/GPNV checksum bad, hit F1 to enter SETUP, F2 to use
default values. I've changed just about everything in SETUP to no avail. If
I hit F2 and take defaults, it will boot and run okay until I have to reboot
again. Then I must go through the same process again. Anyone have any ideas
about this? Thanks! |
|
| Back to top |
|
 | |
External
Since: Dec 18, 2003
Posts: 80
|
(Msg. 2) Posted: Thu Jul 17, 2003 3:43 am
Post subject: Re: SD11 [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
"Dennis" <denaas.DeleteThis@swbell.net> wrote in message news:CbkRa.56$La.27509872@newssvr11.news.prodigy.com...
> Help anyone,
>
> I just put a new SD11 mobo in a Compaq 5900Z, replacing a OE version of the
> SD11 that I thought was bad. It would not reboot. (tries to but would seem
> to go into sleep mode instead) Anyway, SD11 was cheap on ebay so I got one,
> put it in and, viola, it does the same thing! So I cleared the bios setting
> with the jumper, rebooted, and it still goes into sleep mode. (I'm not sure
> it really is in sleep mode, but the monitor goes into low power, and the
> booting process stops. If I clear the bios & hit the switch, it says cmos
> setting bad, cmos/GPNV checksum bad, hit F1 to enter SETUP, F2 to use
> default values. I've changed just about everything in SETUP to no avail. If
> I hit F2 and take defaults, it will boot and run okay until I have to reboot
> again. Then I must go through the same process again. Anyone have any ideas
> about this? Thanks!
>
Have you tried swapping the memory, even a single known good stick might do.
Den
--
artificial hippocampus
I wish I could remember
what is means.<!-- ~MESSAGE_AFTER~ --> |
|
| Back to top |
|
| |
External
Since: Jul 16, 2003
Posts: 4
|
(Msg. 3) Posted: Thu Jul 17, 2003 3:43 am
Post subject: Re: SD11 [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
Yes I have tried memory swaps. No luck though. Thanks for the reply.
"Den" <Den DeleteThis @NoSpamOrNoCornedBeef.unlimited-But-Was-Limited.RIP> wrote in
message news:bf4nks$jh4$1@newsg1.svr.pol.co.uk...
>
> "Dennis" <denaas DeleteThis @swbell.net> wrote in message
news:CbkRa.56$La.27509872@newssvr11.news.prodigy.com...
> > Help anyone,
> >
> > I just put a new SD11 mobo in a Compaq 5900Z, replacing a OE version of
the
> > SD11 that I thought was bad. It would not reboot. (tries to but would
seem
> > to go into sleep mode instead) Anyway, SD11 was cheap on ebay so I got
one,
> > put it in and, viola, it does the same thing! So I cleared the bios
setting
> > with the jumper, rebooted, and it still goes into sleep mode. (I'm not
sure
> > it really is in sleep mode, but the monitor goes into low power, and the
> > booting process stops. If I clear the bios & hit the switch, it says
cmos
> > setting bad, cmos/GPNV checksum bad, hit F1 to enter SETUP, F2 to use
> > default values. I've changed just about everything in SETUP to no
avail. If
> > I hit F2 and take defaults, it will boot and run okay until I have to
reboot
> > again. Then I must go through the same process again. Anyone have any
ideas
> > about this? Thanks!
> >
> Have you tried swapping the memory, even a single known good stick might
do.
>
> Den
> --
> artificial hippocampus
> I wish I could remember
> what is means.
>
>
><!-- ~MESSAGE_AFTER~ --> >> Stay informed about: SD11 |
|
| Back to top |
|
| |
| Related Topics: | VA-503+ won't recognize D-Link network card - What's been your luck in getting the D-Link DWL-G510 wireless PCI netwoerk card to work in an FIC VA-503+ and Windows? I couldn't get Windows to recognize the card, no matter how I installed or uninstalled the driver software, what PCI slot I used (othe...
VIA C3 processor on FIC KA31 motherboard ??? - Has anyone tried the VIA C3 processor (on a slocket) on a KA31 motherboard? I think I know where I can get my hands on an 800MHz processor for a reasonable price and wonder if it's worth trying. Maybe the BIOS doesn't support the processor - I don't..
hmmm... - I have a va503+ with a sb live card and a g-force 4 card. it's clocking 500 MHz with 384 Mb of ram running windows 2000. when I play a song with Windows media player, it plays great. but when I have the graphics turned on, such as the swirly ambient..
AGP Lock on AU13? - Hi It's been a while since I put a system together, and I ran into some problems inserting the AGP video card into my AU13. First, there wasn't enough clearance to insert the card; I had to loosen all of the MB screws and then was able to insert the..
PCI problem on a VA503+ - Hi there, I've got a VA503+ , flashed with the modified APM bios (I can't remember the version - you all know what one it is), with a K6-2 500 (5x100), 256meg PC-100 and WinXP Pro SP1 installed with the F6(?) 'Standard PC' option. I have the lastest VIA... |
|
You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
|
|
|
FAQ
Profile
Private Messages
Log in
