Welcome to PCForumz.com!
FAQFAQ      ProfileProfile    Private MessagesPrivate Messages   Log inLog in

Any suggestions about overclocking 8knxp

 
   Hardware Problem Solving Community! (Home) -> Gigabyte RSS
Next:  Pulling my hair out with GA-7N400 Pro2 + AMD 2600..  
Author Message
steph2

External


Since: Aug 27, 2003
Posts: 3



(Msg. 1) Posted: Thu Sep 11, 2003 2:36 am
Post subject: Any suggestions about overclocking 8knxp
Archived from groups: alt>comp>periphs>mainboard>gigabyte (more info?)

I can't reach 3GHz with 2.4 P4C....
Actually; fsb:241 ratio 5/4 with xms corsair 3200 (2,3,3,6) +0.2V
Vcore just under 2.600 temp: 43°C with intel fan

Any Idea ???????

Steph

 >> Stay informed about: Any suggestions about overclocking 8knxp 
Back to top
Login to vote
Dodgy

External


Since: Jun 30, 2003
Posts: 82



(Msg. 2) Posted: Thu Sep 11, 2003 12:53 pm
Post subject: Re: Any suggestions about overclocking 8knxp [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)

On Wed, 10 Sep 2003 23:36:05 +0200, "steph" <stephbr RemoveThis @noos.fr> waffled
on about something:

 >I can't reach 3GHz with 2.4 P4C....
 >Actually; fsb:241 ratio 5/4 with xms corsair 3200 (2,3,3,6) +0.2V
 > Vcore just under 2.600 temp: 43°C with intel fan
 >
 >Any Idea ???????
 >
 >Steph

Did you try any lower settings successfully before charging in with a
25% overclock?

D0d6y.
--
MUSHROOMS ARE THE OPIATE OF THE MOOSES<!-- ~MESSAGE_AFTER~ -->

 >> Stay informed about: Any suggestions about overclocking 8knxp 
Back to top
Login to vote
Display posts from previous:   
Related Topics:
PAT on 8KNXP - I ran Sandra and found that PAT was turned off...after doing a little searching I found out that if you have four Dimm slots filled you have to have "Fast Chip Select" set to "Enabled"...if it is set to "Auto" PAT is turned ...

GA-8KNXP - is it DOA?? - All, I just bought a few components to throw together : Gigabyte GA-8KNXP Board P4 2.6ghz 800Mhz FSB Geil Ultra Platinum DDR 433 Mhz - 256 X 2 Seagate Barracuda 120 GB Serial ATA HD Antec SmartBlue 350W PS I put all of this with an Old Leadtek winfast...

8KNXP - I have recently setup a 8knxp with intel 3.0 hyp enabled CPU. The cpu fan speeds up and gets extremely noisy and then slows down after a while. I have disabled the system fan control from the BIOS to no effect any suggestions ?

8KNXP and HT - Hi, My 8KNXP system shows only 1 CPU in Task manager, yet 2 CPU's in Device Manager - the CPU is a P4 2.8c. HT has always been enabled in the bios, so I am curious if this is working correctly as it does not appear to. Bios is F5. Does anyone have any....

8KNXP rev 2.0? - Just received one of these as an upgrade to my 8IEXP rev 1.2. Just fired it up, it has BIOS version FB dated 08/12/03 (MM/DD/YY) installed. As usual I had a look around GB's site for a later BIOS version, I am assuming that the BIOS versions on GB's..
   Hardware Problem Solving Community! (Home) -> Gigabyte All times are: Pacific Time (US & Canada) (change)
Page 1 of 1

 
You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



[ Contact us | Terms of Service/Privacy Policy ]